ItalianoShop
Showing 211–240 of 1386 results
-
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
DatasheetSKU: n/a -
Microwave Network Analyzer
HP-Agilent/Keysight 85107B , 8510C , 85102B , 85101C , 8517B
HP 85107B 230 MICROWAVE NETWORK ANALYZER, 45 MHz to 50 GHz.
Complete with:
HP 8510C NETWORK ANALYZER
HP 85102B IF / DETECTOR
HP 8517B S-PARAMETER TEST SET 45 MHz-50GHz OPT 007
HP 85133-60016 2.4mm (f) FLEXIBLE TEST PORT CABLE Qty.2
HP 83651B SYNTHESIZED SWEEPER 10MHz – 50GHz 8360B Qty.1
ACCESSORIES:
Qty.1 INTELLIGENT INTERFACES MICROPRINT45CH VARIABLE RESOLUTION HP-GL / COLOR / SPEED MODES HP-IP TO PARALLEL INTERFACE CONVERTER;
Qty.1x WG K420 GPIB CABLE;
Qty.2x HP 10833A GPIB CABLE;
Qty.1x HP 08510-60101 IF INTERCONNECT DISPLAY;
Qty.1x HP 08510-60102 TEST SET – IF INTERCONNECT;
Qty.2x HP 10503A BNC CABLE;
Qty.1x HP 8710-1764 8lb-in;
Qty.1x HP 8710-1770 9/16 – 1/2;
Qty.1x HUBER & SUHNER SUCOFLEX 104P FLEXIBLE MICROWAVE CABLE ASSEMBLY;
Qty.5x ADAPTER.
DatasheetSKU: n/a -
Oscilloscope 4 channles
Rigol DS6104
DSO with 1GHz bandwidth and 5GSa/s.
The Rigol DS6104 is a very high quality four channel digital storage oscilloscope. It offers up to 5GSa/s real-time sample rate and up to 1GHz bandwidth. These high performances ensure not only to capture real-time instantaneous signal, but also to observe details of repeated signal. DS6104 have up to 120.000 wfms/s refresh rate, which enable users to capture instantaneous signal and abnormal signal more quickly, to enhance waveform capturing ability, and to expedite circuit debug course. The quality of the Rigol Oscilloscopes is comparable to Agilent and Tektronix oscilloscopes. Other advantages: 10.1″ color LCD, bright and vivid waveform display- versatile trigger modes: i.e. slope, alternative, rise&fall edge, enable users to stabilize signal more easily. In economical oscilloscope field, DS6104 have no doubt the highest performances, the most functions thus should be engineers’ best choice. Delivery including 4 probes (bandwidth 600MHz), USB cable, pc software, power adapter and manual. General Data Digital Oscilloscope Digital Oscilloscope Rigol DS6104 Display 10,1″ WVGA-Color-LCD Resolution 800 x 480 Pixel Interface 2x USB-host for i.e. USB sticks USB-Device for a PC connection or USB Pict-Bridge printerinterface LAN for network connectivity (LXI compilant) GPIB (IEE-488, General Purpose Interface Bus) using the optional USB-GPIB Module Trigger- and Calibrationoutput 10MHz reference clock In-/Out VGA interface to connect to an external monitor or projector Size in clarification Weight in clarification Supported operation systems in clarification Oscilloscope Functions Oscilloscope Functions Digital Oscilloscope Rigol DS6104 Channels 4 Real-time sample rate 5 GSa/s realtime Bandwidth 1 GHz Sampling Modus Normal, average, peak detect Mathematics userdefined, FFT (Fast Fourier Transform) FFT algorithm Rectangle, Hanning, Hamming, Blackman Signal Bus Decoding I²C, RS232, SPI, USB, CAN and FlexRay Signal Digital Oscilloscope Rigol DS6104 Input DC/AC coupling, up to 300 Vrms CAT I Real-time sample rate up to 5 GSa/s realtime Time base in clarification Memory 140Mpts (1 Channel) Filter Hardware LPF, HPF, BPF and BRF Vertical Digital Oscilloscope Rigol DS6104 Analog digital converter (A/D) With the resolution of 8 bits, make sampling on both channels synchronously. Sensitivity range (V/div) in clarification Displacement range in clarification Trigger Digital Oscilloscope Rigol DS6104 Trigger in clarification Signal system and line/field frequency (Video triggering mode) in clarification Triggerfunctions Edge, Pattern, Glitch, Puls width, Sequence, Slew rate, I²C, RS232/UART, CAN, FlexRay, USB, SPI, Video Measurement Digital Oscilloscope Rigol DS6104 Cursor measurement Manual, Track and Auto Measure modes Auto measurement Vpp, Vamp, Vmax, Vmin, Vtop, Vbase, Vavg, Vrms, Preshoot, Overshoot, Frequency, Period, Rise Time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Delay1-2 (rise), Delay1-2(fall)SKU: 160 -
Termocamera
Flir E40
(Italiano) A seconda del modello di termocamera della FLIR Serie E, la capacità di risoluzione massima IR è di 320×240 pixels. Queste termocamere sono ideali per la manutenzione predittiva e le ispezioni programmate di impianti elettrici e sistemi meccanici, per assicurarne il corretto funzionamento con la massima efficienza e sicurezza e con il minimo consumo energetico. – Risoluzione massima di 320 x 240 pixels A seconda del modello di termocamera FLIR Serie E, la risoluzione delle immagini IR va da 160×120 pixels a 320×240 pixels. – Piccole ed ultraleggere I modelli FLIR Serie E pesano solo 825gr e possono essere facilmente trasportati all'interno del loro fodero. – Estremamente robusta Le termocamere FLIR Serie E sopportano cadute da due metri. Sono a norma IP54. – Fotocamera di alta qualità Le termocamere FLIR Serie E sono dotate di fotocamera digitale integrata che rende le ispezioni più semplici e veloci. – Galleria immagini Permette di accedere facilmente alle immagini salvate e selezionare quella desiderata. – Precisione ± 2% Accuratezza ±2 °C o ±2% della lettura. – LCD touch screen Ampio LCD touch screen a colori da 3,5″. – Illuminatore a LED incorporato Le termocamere FLIR Serie E sono dotate di illuminatore a LED incorporato che assicura un'alta qualità delle immagini nel visibile, indipendentemente dalla luminosità dell'ambiente di lavoro. – Batteria a lunga durata La batteria al litio ha un'autonomia di 4 ore, è facilmente sostituibile sul posto e vi permetterà di mantenere gli impegni programmati. – Puntatore laser Un pulsante ergonomico attiva il puntatore laser che consente di associare il punto caldo/freddo nell'immagine IR con la posizione fisica dell'oggetto reale nel campo. – FLIR Picture-in-Picture Utilizzando la funzione FLIR Picture-in-Picture, è estremamente semplice localizzare ed evidenziare le aree di interesse. – FLIR Thermal Fusion Fonde le immagini visive e quelle ad infrarossi per consentire un'analisi migliore. – Report immediati Creazione immediata di report direttamente nella termocamera, facilmente copiabili su USB. (FLIR E60) – Annotazioni di testo e commenti vocali Le annotazioni di testo possono essere prese da un elenco predefinito o inserite tramite touch screen. Per i commenti vocali, è possibile collegare una cuffia. – Lenti intercambiabili Per poter utilizzare le termocamere ad infrarossi FLIR Serie E in qualsiasi situazione, sono disponibili la lente grandangolare e il teleobiettivo. – WiFi Connessione a smartphone o tablet tramite Wi-Fi, con l'applicazione FLIR Tools mobile app (Apple iOS e Android) per la gestione e la condivisione dei risultati, oltre che per il controllo remoto.
SKU: 236 -
Oscilloscope 2 channels
TEKTRONIX TDS220
The TDS220 is a 100 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:–Bandwidth: 100 MHz
–2 Channels
–1 GS/s Sample Rate on all Channels
–Record Length: 2.5 kpts
–Dual Timebase
–Automatic Measurements
–Multi-language User Interface
–Autoset
–Waveform and Setup Memories
–Extended Capabilities Are Provided with Optional Modules, Software and Probing Applications
DatasheetSKU: 558
-
-
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
Datasheet -
Microwave Network Analyzer
HP-Agilent/Keysight 85107B , 8510C , 85102B , 85101C , 8517B
HP 85107B 230 MICROWAVE NETWORK ANALYZER, 45 MHz to 50 GHz.
Complete with:
HP 8510C NETWORK ANALYZER
HP 85102B IF / DETECTOR
HP 8517B S-PARAMETER TEST SET 45 MHz-50GHz OPT 007
HP 85133-60016 2.4mm (f) FLEXIBLE TEST PORT CABLE Qty.2
HP 83651B SYNTHESIZED SWEEPER 10MHz – 50GHz 8360B Qty.1
ACCESSORIES:
Qty.1 INTELLIGENT INTERFACES MICROPRINT45CH VARIABLE RESOLUTION HP-GL / COLOR / SPEED MODES HP-IP TO PARALLEL INTERFACE CONVERTER;
Qty.1x WG K420 GPIB CABLE;
Qty.2x HP 10833A GPIB CABLE;
Qty.1x HP 08510-60101 IF INTERCONNECT DISPLAY;
Qty.1x HP 08510-60102 TEST SET – IF INTERCONNECT;
Qty.2x HP 10503A BNC CABLE;
Qty.1x HP 8710-1764 8lb-in;
Qty.1x HP 8710-1770 9/16 – 1/2;
Qty.1x HUBER & SUHNER SUCOFLEX 104P FLEXIBLE MICROWAVE CABLE ASSEMBLY;
Qty.5x ADAPTER.
Datasheet -
Oscilloscope 4 channles
Rigol DS6104
DSO with 1GHz bandwidth and 5GSa/s.
The Rigol DS6104 is a very high quality four channel digital storage oscilloscope. It offers up to 5GSa/s real-time sample rate and up to 1GHz bandwidth. These high performances ensure not only to capture real-time instantaneous signal, but also to observe details of repeated signal. DS6104 have up to 120.000 wfms/s refresh rate, which enable users to capture instantaneous signal and abnormal signal more quickly, to enhance waveform capturing ability, and to expedite circuit debug course. The quality of the Rigol Oscilloscopes is comparable to Agilent and Tektronix oscilloscopes. Other advantages: 10.1″ color LCD, bright and vivid waveform display- versatile trigger modes: i.e. slope, alternative, rise&fall edge, enable users to stabilize signal more easily. In economical oscilloscope field, DS6104 have no doubt the highest performances, the most functions thus should be engineers’ best choice. Delivery including 4 probes (bandwidth 600MHz), USB cable, pc software, power adapter and manual. General Data Digital Oscilloscope Digital Oscilloscope Rigol DS6104 Display 10,1″ WVGA-Color-LCD Resolution 800 x 480 Pixel Interface 2x USB-host for i.e. USB sticks USB-Device for a PC connection or USB Pict-Bridge printerinterface LAN for network connectivity (LXI compilant) GPIB (IEE-488, General Purpose Interface Bus) using the optional USB-GPIB Module Trigger- and Calibrationoutput 10MHz reference clock In-/Out VGA interface to connect to an external monitor or projector Size in clarification Weight in clarification Supported operation systems in clarification Oscilloscope Functions Oscilloscope Functions Digital Oscilloscope Rigol DS6104 Channels 4 Real-time sample rate 5 GSa/s realtime Bandwidth 1 GHz Sampling Modus Normal, average, peak detect Mathematics userdefined, FFT (Fast Fourier Transform) FFT algorithm Rectangle, Hanning, Hamming, Blackman Signal Bus Decoding I²C, RS232, SPI, USB, CAN and FlexRay Signal Digital Oscilloscope Rigol DS6104 Input DC/AC coupling, up to 300 Vrms CAT I Real-time sample rate up to 5 GSa/s realtime Time base in clarification Memory 140Mpts (1 Channel) Filter Hardware LPF, HPF, BPF and BRF Vertical Digital Oscilloscope Rigol DS6104 Analog digital converter (A/D) With the resolution of 8 bits, make sampling on both channels synchronously. Sensitivity range (V/div) in clarification Displacement range in clarification Trigger Digital Oscilloscope Rigol DS6104 Trigger in clarification Signal system and line/field frequency (Video triggering mode) in clarification Triggerfunctions Edge, Pattern, Glitch, Puls width, Sequence, Slew rate, I²C, RS232/UART, CAN, FlexRay, USB, SPI, Video Measurement Digital Oscilloscope Rigol DS6104 Cursor measurement Manual, Track and Auto Measure modes Auto measurement Vpp, Vamp, Vmax, Vmin, Vtop, Vbase, Vavg, Vrms, Preshoot, Overshoot, Frequency, Period, Rise Time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Delay1-2 (rise), Delay1-2(fall) -
Termocamera
Flir E40
(Italiano) A seconda del modello di termocamera della FLIR Serie E, la capacità di risoluzione massima IR è di 320×240 pixels. Queste termocamere sono ideali per la manutenzione predittiva e le ispezioni programmate di impianti elettrici e sistemi meccanici, per assicurarne il corretto funzionamento con la massima efficienza e sicurezza e con il minimo consumo energetico. – Risoluzione massima di 320 x 240 pixels A seconda del modello di termocamera FLIR Serie E, la risoluzione delle immagini IR va da 160×120 pixels a 320×240 pixels. – Piccole ed ultraleggere I modelli FLIR Serie E pesano solo 825gr e possono essere facilmente trasportati all'interno del loro fodero. – Estremamente robusta Le termocamere FLIR Serie E sopportano cadute da due metri. Sono a norma IP54. – Fotocamera di alta qualità Le termocamere FLIR Serie E sono dotate di fotocamera digitale integrata che rende le ispezioni più semplici e veloci. – Galleria immagini Permette di accedere facilmente alle immagini salvate e selezionare quella desiderata. – Precisione ± 2% Accuratezza ±2 °C o ±2% della lettura. – LCD touch screen Ampio LCD touch screen a colori da 3,5″. – Illuminatore a LED incorporato Le termocamere FLIR Serie E sono dotate di illuminatore a LED incorporato che assicura un'alta qualità delle immagini nel visibile, indipendentemente dalla luminosità dell'ambiente di lavoro. – Batteria a lunga durata La batteria al litio ha un'autonomia di 4 ore, è facilmente sostituibile sul posto e vi permetterà di mantenere gli impegni programmati. – Puntatore laser Un pulsante ergonomico attiva il puntatore laser che consente di associare il punto caldo/freddo nell'immagine IR con la posizione fisica dell'oggetto reale nel campo. – FLIR Picture-in-Picture Utilizzando la funzione FLIR Picture-in-Picture, è estremamente semplice localizzare ed evidenziare le aree di interesse. – FLIR Thermal Fusion Fonde le immagini visive e quelle ad infrarossi per consentire un'analisi migliore. – Report immediati Creazione immediata di report direttamente nella termocamera, facilmente copiabili su USB. (FLIR E60) – Annotazioni di testo e commenti vocali Le annotazioni di testo possono essere prese da un elenco predefinito o inserite tramite touch screen. Per i commenti vocali, è possibile collegare una cuffia. – Lenti intercambiabili Per poter utilizzare le termocamere ad infrarossi FLIR Serie E in qualsiasi situazione, sono disponibili la lente grandangolare e il teleobiettivo. – WiFi Connessione a smartphone o tablet tramite Wi-Fi, con l'applicazione FLIR Tools mobile app (Apple iOS e Android) per la gestione e la condivisione dei risultati, oltre che per il controllo remoto.
-
Oscilloscope 2 channels
TEKTRONIX TDS220
The TDS220 is a 100 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:–Bandwidth: 100 MHz
–2 Channels
–1 GS/s Sample Rate on all Channels
–Record Length: 2.5 kpts
–Dual Timebase
–Automatic Measurements
–Multi-language User Interface
–Autoset
–Waveform and Setup Memories
–Extended Capabilities Are Provided with Optional Modules, Software and Probing Applications
Datasheet
-
-
Network Analyzer
HP/Agilent-Keysight 8753ES
Agilent 8753ES vector network analyzers perform complete characterization of RF components.
30 kHz to 3 GHz
Frequency and power sweepsSpecifications describe the instrument’s warranted performance after a half-hour warm-up and over the temperature range of 25° ± 5° C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance). Supplemental characteristics are typical but nonwarranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.” The measurement uncertainty curves and measurement port characteristics given for Agilent Technologies 8753ES systems also apply to the 8753ES with Options 006 and 011 and the 85047A test set (50-ohm), or the 8753ES Option 011 with an 85046B test set (75-ohm).
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity. Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the 8753ES and enhancedresponse error correction for the 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worst-case model for the contributions of dynamic accuracy and residual systematic errors. Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the 8753ES and enhanced-response error correction for the 8753ET. These characteristics apply for an environmental temperature of 25° ± 5° C, with less than 1° C deviation from the calibration temperature. Agilent 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking. Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise. Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
Datasheet -
Microwave Network Analyzer
HP-Agilent/Keysight 85107B , 8510C , 85102B , 85101C , 8517B
HP 85107B 230 MICROWAVE NETWORK ANALYZER, 45 MHz to 50 GHz.
Complete with:
HP 8510C NETWORK ANALYZER
HP 85102B IF / DETECTOR
HP 8517B S-PARAMETER TEST SET 45 MHz-50GHz OPT 007
HP 85133-60016 2.4mm (f) FLEXIBLE TEST PORT CABLE Qty.2
HP 83651B SYNTHESIZED SWEEPER 10MHz – 50GHz 8360B Qty.1
ACCESSORIES:
Qty.1 INTELLIGENT INTERFACES MICROPRINT45CH VARIABLE RESOLUTION HP-GL / COLOR / SPEED MODES HP-IP TO PARALLEL INTERFACE CONVERTER;
Qty.1x WG K420 GPIB CABLE;
Qty.2x HP 10833A GPIB CABLE;
Qty.1x HP 08510-60101 IF INTERCONNECT DISPLAY;
Qty.1x HP 08510-60102 TEST SET – IF INTERCONNECT;
Qty.2x HP 10503A BNC CABLE;
Qty.1x HP 8710-1764 8lb-in;
Qty.1x HP 8710-1770 9/16 – 1/2;
Qty.1x HUBER & SUHNER SUCOFLEX 104P FLEXIBLE MICROWAVE CABLE ASSEMBLY;
Qty.5x ADAPTER.
Datasheet -
Oscilloscope 4 channles
Rigol DS6104
DSO with 1GHz bandwidth and 5GSa/s.
The Rigol DS6104 is a very high quality four channel digital storage oscilloscope. It offers up to 5GSa/s real-time sample rate and up to 1GHz bandwidth. These high performances ensure not only to capture real-time instantaneous signal, but also to observe details of repeated signal. DS6104 have up to 120.000 wfms/s refresh rate, which enable users to capture instantaneous signal and abnormal signal more quickly, to enhance waveform capturing ability, and to expedite circuit debug course. The quality of the Rigol Oscilloscopes is comparable to Agilent and Tektronix oscilloscopes. Other advantages: 10.1″ color LCD, bright and vivid waveform display- versatile trigger modes: i.e. slope, alternative, rise&fall edge, enable users to stabilize signal more easily. In economical oscilloscope field, DS6104 have no doubt the highest performances, the most functions thus should be engineers’ best choice. Delivery including 4 probes (bandwidth 600MHz), USB cable, pc software, power adapter and manual. General Data Digital Oscilloscope Digital Oscilloscope Rigol DS6104 Display 10,1″ WVGA-Color-LCD Resolution 800 x 480 Pixel Interface 2x USB-host for i.e. USB sticks USB-Device for a PC connection or USB Pict-Bridge printerinterface LAN for network connectivity (LXI compilant) GPIB (IEE-488, General Purpose Interface Bus) using the optional USB-GPIB Module Trigger- and Calibrationoutput 10MHz reference clock In-/Out VGA interface to connect to an external monitor or projector Size in clarification Weight in clarification Supported operation systems in clarification Oscilloscope Functions Oscilloscope Functions Digital Oscilloscope Rigol DS6104 Channels 4 Real-time sample rate 5 GSa/s realtime Bandwidth 1 GHz Sampling Modus Normal, average, peak detect Mathematics userdefined, FFT (Fast Fourier Transform) FFT algorithm Rectangle, Hanning, Hamming, Blackman Signal Bus Decoding I²C, RS232, SPI, USB, CAN and FlexRay Signal Digital Oscilloscope Rigol DS6104 Input DC/AC coupling, up to 300 Vrms CAT I Real-time sample rate up to 5 GSa/s realtime Time base in clarification Memory 140Mpts (1 Channel) Filter Hardware LPF, HPF, BPF and BRF Vertical Digital Oscilloscope Rigol DS6104 Analog digital converter (A/D) With the resolution of 8 bits, make sampling on both channels synchronously. Sensitivity range (V/div) in clarification Displacement range in clarification Trigger Digital Oscilloscope Rigol DS6104 Trigger in clarification Signal system and line/field frequency (Video triggering mode) in clarification Triggerfunctions Edge, Pattern, Glitch, Puls width, Sequence, Slew rate, I²C, RS232/UART, CAN, FlexRay, USB, SPI, Video Measurement Digital Oscilloscope Rigol DS6104 Cursor measurement Manual, Track and Auto Measure modes Auto measurement Vpp, Vamp, Vmax, Vmin, Vtop, Vbase, Vavg, Vrms, Preshoot, Overshoot, Frequency, Period, Rise Time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Delay1-2 (rise), Delay1-2(fall) -
Termocamera
Flir E40
(Italiano) A seconda del modello di termocamera della FLIR Serie E, la capacità di risoluzione massima IR è di 320×240 pixels. Queste termocamere sono ideali per la manutenzione predittiva e le ispezioni programmate di impianti elettrici e sistemi meccanici, per assicurarne il corretto funzionamento con la massima efficienza e sicurezza e con il minimo consumo energetico. – Risoluzione massima di 320 x 240 pixels A seconda del modello di termocamera FLIR Serie E, la risoluzione delle immagini IR va da 160×120 pixels a 320×240 pixels. – Piccole ed ultraleggere I modelli FLIR Serie E pesano solo 825gr e possono essere facilmente trasportati all'interno del loro fodero. – Estremamente robusta Le termocamere FLIR Serie E sopportano cadute da due metri. Sono a norma IP54. – Fotocamera di alta qualità Le termocamere FLIR Serie E sono dotate di fotocamera digitale integrata che rende le ispezioni più semplici e veloci. – Galleria immagini Permette di accedere facilmente alle immagini salvate e selezionare quella desiderata. – Precisione ± 2% Accuratezza ±2 °C o ±2% della lettura. – LCD touch screen Ampio LCD touch screen a colori da 3,5″. – Illuminatore a LED incorporato Le termocamere FLIR Serie E sono dotate di illuminatore a LED incorporato che assicura un'alta qualità delle immagini nel visibile, indipendentemente dalla luminosità dell'ambiente di lavoro. – Batteria a lunga durata La batteria al litio ha un'autonomia di 4 ore, è facilmente sostituibile sul posto e vi permetterà di mantenere gli impegni programmati. – Puntatore laser Un pulsante ergonomico attiva il puntatore laser che consente di associare il punto caldo/freddo nell'immagine IR con la posizione fisica dell'oggetto reale nel campo. – FLIR Picture-in-Picture Utilizzando la funzione FLIR Picture-in-Picture, è estremamente semplice localizzare ed evidenziare le aree di interesse. – FLIR Thermal Fusion Fonde le immagini visive e quelle ad infrarossi per consentire un'analisi migliore. – Report immediati Creazione immediata di report direttamente nella termocamera, facilmente copiabili su USB. (FLIR E60) – Annotazioni di testo e commenti vocali Le annotazioni di testo possono essere prese da un elenco predefinito o inserite tramite touch screen. Per i commenti vocali, è possibile collegare una cuffia. – Lenti intercambiabili Per poter utilizzare le termocamere ad infrarossi FLIR Serie E in qualsiasi situazione, sono disponibili la lente grandangolare e il teleobiettivo. – WiFi Connessione a smartphone o tablet tramite Wi-Fi, con l'applicazione FLIR Tools mobile app (Apple iOS e Android) per la gestione e la condivisione dei risultati, oltre che per il controllo remoto.
-
Oscilloscope 2 channels
TEKTRONIX TDS220
The TDS220 is a 100 MHz, 2 channel digital oscilloscope from Tektronix. Measure voltage or current signals over time in an electronic circuit or component to display amplitude, frequency and rise times, etc. Applications include troubleshooting, production test, and design.
Additional Features:–Bandwidth: 100 MHz
–2 Channels
–1 GS/s Sample Rate on all Channels
–Record Length: 2.5 kpts
–Dual Timebase
–Automatic Measurements
–Multi-language User Interface
–Autoset
–Waveform and Setup Memories
–Extended Capabilities Are Provided with Optional Modules, Software and Probing Applications
Datasheet