ItalianoShop
Showing 1051–1080 of 1386 results
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and controlSKU: 1142 -
Attenuator
HP 8494G Programmable Step Attenuator, DC to 4 GHz
The 8494G dc to 4 GHz programmable step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. A maximum switching time of 20 ms (including contact settling) speeds automatic testing. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
* Frequency range: dc to 4 GHz
* Insertion loss at 0 dB: 0.6 dB + 0.09 dB/GHz
* Maximum SWR: 1.5
* Repeatability life: 0.03 dB max 5 million cycles per section, typical
* 5 million cycles per section
* Maximum RF input power: 1 W (average), 100 W (peak)
* Connector type: choice of Type-N female, SMA female, APC-7
* Programming connector: 12-pin Viking, optional 14-pin DIPSKU: n/a -
Senza categoria
IFR FM/AM1200S Communications Service Monitor, 250 kHz -1 GHz
The IFR FM/AM-1200S is a bench tester multi-function, microprocessor controlled Communications Service Monitors designed to meet the requirements of most radio maintenance applications throughout the RF frequency range of 250 kHz to 1 GHz.
Functions from mobile, aircraft or marine is achievable straight from 11 to 28 volt DC power systems, using a furnished cigar lighter adaptor plug. AC power function is probable from 115/230 VAC 47 to 420 Hz power services.* FM and AM Signal Generator
* 2 µV Receiver for AM, FM, and SSB
* RF Frequency Error Meter with 1 Hz ResolutionSKU: n/a -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
DatasheetSKU: n/a -
Oscilloscope 4 channles
TEKTRONIX 2465A
The Tektronix 2465A is a four-channel 350 MHz portable oscilloscope. The 2445A and 2455A are 150 and 250 MHz versions.
The horizontal amplifier in the 2465A was designed by Art Metz and Ken Schlotzhauer.
Art Metz also worked on the triggers. Art Metz and Walt Ainsworth designed the sweeps.Sweep Rate 500 ps/div
Channels Four independent channels
Vertical 2 mV/div vertical sensitivity
Cursors Delta Volts and Delta Time Cursors
CRT Readout Scale Factors, Trigger Level, Voltage, Time, Frequency, Phase and Ratio Measurements and Mode Indicators
Trigger Advanced Triggering with “Hands Off” Auto Level Triggering
Trigger Bandwidth 500 MHz min.
Input Impedance 50 Ω/1 MΩ inputs with 50 Ω protection
Probes Two or four P6136 ×10 probes, 1.3 m
DatasheetSKU: n/a -
Oscilloscope 2 channels
KENWOOD CS-4125
Kenwood CS-4125 20MHz 2-Channel Analog Oscilloscope. Kenwood CS-4125 20MHz 2-Channel Oscilloscope Features High reliability with Kenwood Original Hibrid ICs High-intensity CRT (12 kV) (with scale illumination) Dynamic range with a headroom for accurate waveform display without distortion High sensitivity of 1 mV/div (DC to 5 MHz) Maximum sweep rate of 20 ns/div (x10 MAG) FIX sync One-touch TV sync Convenient VERT mode One-touch ALT/CHOP switching X-Y Mode Vertical axis signal output connector Waveforms can be observed by applying intensity modulation. Added or subtracted waveforms can be observed. The trace inclination can be corrected with the front panel operation. Relay-type attenuators with long life and excellent operability are used. Kenwood TMI Corp. CS-4125 Oscilloscope, Analog: 20MHz, 2 Channel (Stand alone) The Kenwood TMI Corp. CS-4125 oscilloscope is a graph-displaying device – it draws a graph of an electrical signal. In most applications, the graph shows how signals change over time: the vertical (Y) axis represents voltage and the horizontal (X) axis represents time. The intensity or brightness of the display is sometimes called the Z axis. The Kenwood TMI Corp. CS-4125 oscilloscope’s simple graph can tell you many things about a signal, such as: the time and voltage values of a signal, the frequency of an oscillating signal, the “moving parts” of a circuit represented by the signal, the frequency with which a particular portion of the signal is occurring relative to, other portions,
DatasheetSKU: n/a
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and control -
Attenuator
HP 8494G Programmable Step Attenuator, DC to 4 GHz
The 8494G dc to 4 GHz programmable step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. A maximum switching time of 20 ms (including contact settling) speeds automatic testing. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
* Frequency range: dc to 4 GHz
* Insertion loss at 0 dB: 0.6 dB + 0.09 dB/GHz
* Maximum SWR: 1.5
* Repeatability life: 0.03 dB max 5 million cycles per section, typical
* 5 million cycles per section
* Maximum RF input power: 1 W (average), 100 W (peak)
* Connector type: choice of Type-N female, SMA female, APC-7
* Programming connector: 12-pin Viking, optional 14-pin DIP -
Senza categoria
IFR FM/AM1200S Communications Service Monitor, 250 kHz -1 GHz
The IFR FM/AM-1200S is a bench tester multi-function, microprocessor controlled Communications Service Monitors designed to meet the requirements of most radio maintenance applications throughout the RF frequency range of 250 kHz to 1 GHz.
Functions from mobile, aircraft or marine is achievable straight from 11 to 28 volt DC power systems, using a furnished cigar lighter adaptor plug. AC power function is probable from 115/230 VAC 47 to 420 Hz power services.* FM and AM Signal Generator
* 2 µV Receiver for AM, FM, and SSB
* RF Frequency Error Meter with 1 Hz Resolution -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Oscilloscope 4 channles
TEKTRONIX 2465A
The Tektronix 2465A is a four-channel 350 MHz portable oscilloscope. The 2445A and 2455A are 150 and 250 MHz versions.
The horizontal amplifier in the 2465A was designed by Art Metz and Ken Schlotzhauer.
Art Metz also worked on the triggers. Art Metz and Walt Ainsworth designed the sweeps.Sweep Rate 500 ps/div
Channels Four independent channels
Vertical 2 mV/div vertical sensitivity
Cursors Delta Volts and Delta Time Cursors
CRT Readout Scale Factors, Trigger Level, Voltage, Time, Frequency, Phase and Ratio Measurements and Mode Indicators
Trigger Advanced Triggering with “Hands Off” Auto Level Triggering
Trigger Bandwidth 500 MHz min.
Input Impedance 50 Ω/1 MΩ inputs with 50 Ω protection
Probes Two or four P6136 ×10 probes, 1.3 m
Datasheet -
Oscilloscope 2 channels
KENWOOD CS-4125
Kenwood CS-4125 20MHz 2-Channel Analog Oscilloscope. Kenwood CS-4125 20MHz 2-Channel Oscilloscope Features High reliability with Kenwood Original Hibrid ICs High-intensity CRT (12 kV) (with scale illumination) Dynamic range with a headroom for accurate waveform display without distortion High sensitivity of 1 mV/div (DC to 5 MHz) Maximum sweep rate of 20 ns/div (x10 MAG) FIX sync One-touch TV sync Convenient VERT mode One-touch ALT/CHOP switching X-Y Mode Vertical axis signal output connector Waveforms can be observed by applying intensity modulation. Added or subtracted waveforms can be observed. The trace inclination can be corrected with the front panel operation. Relay-type attenuators with long life and excellent operability are used. Kenwood TMI Corp. CS-4125 Oscilloscope, Analog: 20MHz, 2 Channel (Stand alone) The Kenwood TMI Corp. CS-4125 oscilloscope is a graph-displaying device – it draws a graph of an electrical signal. In most applications, the graph shows how signals change over time: the vertical (Y) axis represents voltage and the horizontal (X) axis represents time. The intensity or brightness of the display is sometimes called the Z axis. The Kenwood TMI Corp. CS-4125 oscilloscope’s simple graph can tell you many things about a signal, such as: the time and voltage values of a signal, the frequency of an oscillating signal, the “moving parts” of a circuit represented by the signal, the frequency with which a particular portion of the signal is occurring relative to, other portions,
Datasheet
-
Module
AGILENT 34903A – 20 Channel Actuator/GP Switch Module for 34970A/34972A
The Agilent 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
* 20 Channel Actuator/GP Switch
* SPDT (Form C) latching relays
* 300 V, 1 A actuation and control -
Attenuator
HP 8494G Programmable Step Attenuator, DC to 4 GHz
The 8494G dc to 4 GHz programmable step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. A maximum switching time of 20 ms (including contact settling) speeds automatic testing. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
* Frequency range: dc to 4 GHz
* Insertion loss at 0 dB: 0.6 dB + 0.09 dB/GHz
* Maximum SWR: 1.5
* Repeatability life: 0.03 dB max 5 million cycles per section, typical
* 5 million cycles per section
* Maximum RF input power: 1 W (average), 100 W (peak)
* Connector type: choice of Type-N female, SMA female, APC-7
* Programming connector: 12-pin Viking, optional 14-pin DIP -
Senza categoria
IFR FM/AM1200S Communications Service Monitor, 250 kHz -1 GHz
The IFR FM/AM-1200S is a bench tester multi-function, microprocessor controlled Communications Service Monitors designed to meet the requirements of most radio maintenance applications throughout the RF frequency range of 250 kHz to 1 GHz.
Functions from mobile, aircraft or marine is achievable straight from 11 to 28 volt DC power systems, using a furnished cigar lighter adaptor plug. AC power function is probable from 115/230 VAC 47 to 420 Hz power services.* FM and AM Signal Generator
* 2 µV Receiver for AM, FM, and SSB
* RF Frequency Error Meter with 1 Hz Resolution -
Power Supply
TDK-Lambda GEN-60-40-1P230
Programmable Lab Power Supply 0-60 V DC 0-40 A
This 2400 W lab power supply sets new standards. They are currently the most powerful 1 HU lab power supplies on the market. Another advantage is that you can stack one device on top of another which means that it needs no air slit either above or below and can actually get by on 1 HU.
Output voltages of up to 60 V and output currents of up to 40 A can be adjusted directly on the device or remotely via the built-in RS232/RS485 interface. All important functions can also be programmed via analogue inputs (control voltage 0 5V, 0-10V, control current 4-20 mA or via external resistor; relevant drivers are available for the digital control e.g., via LabView and LabWindows). High-resolution 16-bit A/D and D/A converters enable very precise settings and programming; the dial controls on the device can be switched between coarse and fine adjustment.
A dual digital display shows the current values, and various status information (andOver Voltage Protection, Under Voltage Limit, overload mode, address settings again), and a monitor output provides corresponding analog voltages (0 – 5 V or 0 – 10 V) for an external monitoring The device can naturally be operated as a constant voltage as well as a constant current source and can, if necessary, automatically switch between these operating modes. Several devices can be switched serially or in parallel. This GEN/H model is half the structural shape of 19″ racks.
Datasheet -
Oscilloscope 4 channles
TEKTRONIX 2465A
The Tektronix 2465A is a four-channel 350 MHz portable oscilloscope. The 2445A and 2455A are 150 and 250 MHz versions.
The horizontal amplifier in the 2465A was designed by Art Metz and Ken Schlotzhauer.
Art Metz also worked on the triggers. Art Metz and Walt Ainsworth designed the sweeps.Sweep Rate 500 ps/div
Channels Four independent channels
Vertical 2 mV/div vertical sensitivity
Cursors Delta Volts and Delta Time Cursors
CRT Readout Scale Factors, Trigger Level, Voltage, Time, Frequency, Phase and Ratio Measurements and Mode Indicators
Trigger Advanced Triggering with “Hands Off” Auto Level Triggering
Trigger Bandwidth 500 MHz min.
Input Impedance 50 Ω/1 MΩ inputs with 50 Ω protection
Probes Two or four P6136 ×10 probes, 1.3 m
Datasheet -
Oscilloscope 2 channels
KENWOOD CS-4125
Kenwood CS-4125 20MHz 2-Channel Analog Oscilloscope. Kenwood CS-4125 20MHz 2-Channel Oscilloscope Features High reliability with Kenwood Original Hibrid ICs High-intensity CRT (12 kV) (with scale illumination) Dynamic range with a headroom for accurate waveform display without distortion High sensitivity of 1 mV/div (DC to 5 MHz) Maximum sweep rate of 20 ns/div (x10 MAG) FIX sync One-touch TV sync Convenient VERT mode One-touch ALT/CHOP switching X-Y Mode Vertical axis signal output connector Waveforms can be observed by applying intensity modulation. Added or subtracted waveforms can be observed. The trace inclination can be corrected with the front panel operation. Relay-type attenuators with long life and excellent operability are used. Kenwood TMI Corp. CS-4125 Oscilloscope, Analog: 20MHz, 2 Channel (Stand alone) The Kenwood TMI Corp. CS-4125 oscilloscope is a graph-displaying device – it draws a graph of an electrical signal. In most applications, the graph shows how signals change over time: the vertical (Y) axis represents voltage and the horizontal (X) axis represents time. The intensity or brightness of the display is sometimes called the Z axis. The Kenwood TMI Corp. CS-4125 oscilloscope’s simple graph can tell you many things about a signal, such as: the time and voltage values of a signal, the frequency of an oscillating signal, the “moving parts” of a circuit represented by the signal, the frequency with which a particular portion of the signal is occurring relative to, other portions,
Datasheet